SFP-GPP-85192-SRT
This 850 nm VCSEL 10Gigabit SFP+ transceiver is designed to transmit and receive optical data over 50/125 μm or 62.5/125 μm multimode optical fiber
The SFP+ SR module electrical interface is compliant to SFI electrical specifications. The transmitter input and receiver output impedance is 100 Ohms differential.Data lines are internally AC coupled. The module provides differential termination and reduce differential to common mode conversion for quality signal termination and low EMI.SFI typically operates over 200 mm of improved FR4 material or up to about 150mmof standard FR4 with one connector.
The transmitter converts 10Gbit/s serial PECL or CML electrical data into serial optical data compliant with the 10GBASE-SR standard.An open collector compatible Transmit Disable (Tx_Dis) is provided. A logic “1,” or no connection on this pin will disable the laser from transmitting. A logic “0” on this pin provides normal operation. The transmitter has an internal automatic power control loop (APC) to ensure constant optical power output across supply voltage and temperature variations.An open collector compatible Transmit Fault (TFault) is provided.TX_Fault is a module output contact that when high, indicates that the module transmitter has detected a fault condition related to laser operation or safety.The TX_Fault output contact is an open drain/collector and shall be pulled up to the Vcc_Host in the host with a resistor in the range 4.7-10 kΩ. TX_Disable is a module input contact.When TX_Disable is asserted high or left open, the SFP+ module transmitter output shall be turned off. This contact shall be ulled up to VccT with a 4.7 kΩ to 10 kΩ resistor.
The receiver converts 10Gbit/s serial optical data into serial PECL/CML electrical data.An open collector compatible Loss of Signal is provided.Rx_LOS when high indicates an optical signal level below that specified in the relevant standard.The Rx_LOS contact is an open drain/collector output and shall be pulled up to Vcc_Host in the host with a resistor in the range 4.7-10 kΩ, or with an active termination.Power supply filtering is recommended for both the transmitter and receiver.
The Rx_LOS signal is intended as a preliminary indication to the system in which the SFP+ is installed that the received signal strength is below the specified range. Such an indication typically points to non-installed cables, broken cables, or a disabled, failing or a powered off transmitter at the far end of the cable.
SFP-GPP-85192-SRT
Optical interface compliant to IEEE 802.3ae 10GBASE-SR
Electrical interface compliant to SFF-8431
Hot Pluggable
850nm VCSEL transmitter, PIN photo-detector
Maximum link length of 300m on OM3 MMF
Industrial operating case temperature range: -40 to 85 °C
Low power consumption
Maximum link length of 300m on 2000MHz/km MMF
All-metal housing for superior EMI performance
Advanced firmware allow customer system encryption information to be stored in transceiver
Cost effective SFP+ solution, enables higher port densities and greater bandwidth
RoHS-6 compliant (lead free)
Pin Descriptions
| Pin |
Symbol |
Name/Description |
| 1 |
VEET [1] |
Transmitter Ground |
| 2 |
Tx_FAULT [2] |
Transmitter Fault |
| 3 |
Tx_DIS [3] |
Transmitter Disable. Laser output disabled on high or open |
| 4 |
SDA [2] |
2-wire Serial Interface Data Line |
| 5 |
SCL [2] |
2-wire Serial Interface Clock Line |
| 6 |
MOD_ABS [4] |
Module Absent. Grounded within the module |
| 7 |
RS0 [5] |
Rate Select 0 |
| 8 |
RX_LOS [2] |
Loss of Signal indication. Logic 0 indicates normal operation |
| 9 |
RS1 [5] |
Rate Select 1 |
| 10 |
VEER [1] |
Receiver Ground |
| 11 |
VEER [1] |
Receiver Ground |
| 12 |
RD- |
Receiver Inverted DATA out. AC Coupled |
| 13 |
RD+ |
Receiver DATA out. AC Coupled |
| 14 |
VEER [1] |
Receiver Ground |
| 15 |
VCCR |
Receiver Power Supply |
| 16 |
VCCT |
Transmitter Power Supply |
| 17 |
VEET [1] |
Transmitter Ground |
| 18 |
TD+ |
Transmitter DATA in. AC Coupled |
| 19 |
TD- |
Transmitter Inverted DATA in. AC Coupled |
| 20 |
VEET [1] |
Transmitter Ground |
Notes:
[1] Module circuit ground is isolated from module chassis ground within the module.
[2].should be pulled up with 4.7k – 10k ohms on host board to a voltage between 3.15Vand 3.6V. [3]Tx_Disable is an input contact with a 4.7 kΩ to 10 kΩ pullup to VccT inside the module.
- Mod_ABS is connected to VeeT or VeeR in the SFP+ module. The host may pull this contact up to Vcc_Host with a resistor in the range 4.7 kΩ to10 kΩ.Mod_ABS is asserted “High” when the SFP+ module is physically absent from a host slot.
- RS0 and RS1 are module inputs and are pulled low to VeeT with > 30 kΩ resistors in the module.
Ordering Information:
| Part Number |
Product Description |
| SFP-GPP-85192-SRT |
SFP+ SR, 10.3Gb/s, 850nm, 300m (OM3), MMF, Duplex LC, -40°C to 85°C |
